Parts and "Go To Guys" !

On this post, I wanted to turn the spotlight on three vendors who have provided first class work for Tillie's restoration. All three of these guys have been easy to work with and have a proven track record in the British car community. I have no financial interest in any of these companies but am just a satisfied customer!

One component that makes an engine run is spark via a distributor....a.k.a "dizzy" in Brit speak. Jeff Schlemmer of Advanced Distributors is considered by many to be the "go to" guy for distributor rebuild work, so I filled out his very detailed "curve" work sheet, packed it up along my distributor, and sent them off to Minnesota. Jeff's worksheet allows him to build your dizzy to match any performance enhancements you've added to your car's engine. In my case, I found out my dizzy was not even the correct one for my car!

Old dizzy


Jeff supplied a correct core, did the  rebuild / recurve, then topped it off with a nice polished finish.





The TR6 came from the factory with two Zenith Stromberg carburetors, and one way of increasing horse power with a modified engine is to add a third ZS carb.  Jeff Palya is the owner of Paltech Technologies, and one of his specialties is carburetor rebuilding for British cars. Jeff is considered by many as the "go to" guy for this critical component of any engine. So, off went my old carbs to be rebuilt and used as part of  a triple conversion.

My original two carb setup



The new Triple carbs will not only provide more power, but look terrific !

Jeff uses an exclusive micropolish process to make old parts look better than new.




My final "go to" guy on this post is Scott at Brake Materials and Parts located in Fort Wayne Indiana.
Like all the parts on a 38 -year -old car, my brake servo(power) unit was looking pretty tough. However,  uppermost in my mind were the internal components and if they were up to the job of stopping my car! Since this is another part  that needs professional attention, I packed up my servo and sent it to Indiana. 




Ten days later, I got back my brake servo unit with power coating on the outside, and most importantly, all new components on the inside!



 Again, a big "thank you" to the TR6/250 Car Club of America  (6-Pack Club) for all the great information on it's web site. These "go to guys" have all been recommended by other 6-Pack members.  

Tillie Comes Home !

Friday, May 11, 2012 was a HUGE day for me.  This is the day I've been anticipating since November... my TR6 body and paint work is finished! John had called me several days before and confirmed the car would be ready for me to pick up on Friday, and even the weather cooperated with 74 degrees and clear skies. 




Wife Rhoda went along to keep me from bouncing off the truck cab roof with excitement, and I was very happy once I had backed into my own driveway without incident.



Oh, did I mention I had the car painted black?  Yeah, I know, black wasn't a color option on the TR6, but  I've always had a "thing" for black cars. So, Tillie has gone from the original maple brown she left the factory with to "exotic red" that the previous owner had applied, to black...do I look pleased ?


John told me I'd need to clean up some of the dust / etc. from the final rubbing, so I put the car on jack stands so I could get into the wheel wells.


I mentioned in a earlier post that Lizard Skin was applied to the top and bottom of the tub floor, inside the wheel wells, and inside all four fender panels. I had John paint the Skin with single stage urethane paint to give those surfaces some shine...

  

I guess now it's no surprise why I painted the engine red... 


Three coats of black base, followed by three coats of clear, followed by color sanding, and the final rubbing...all done by John, my body man / painter, craftsman, artist extraordinaire!  Now it's up to me to make this beauty a runner.



Body Shop Update

Back at the body shop, the tub has been up on a jig so John could get underneath it to finish up welding, cleaning up the welds, and getting it ready for paint.





 One important part of the pre-paint process was spraying Lizard Skin ceramic insulation on the floor (top and bottom) from the firewall back to, and including, the trunk area. The exhaust pipes run right under the passenger's floor area, and the Lizard Skin will keep the heat under control, in addition to helping with sound insulation and corrosion control. John also applied the Lizard Skin in the wheel wells and inside the fender panels.


The Lizard Skin dries to a flat black, so I asked John if he could make it shiny. He said sure, and he sprayed single stage black urethane paint over the "Skin". In the photo below, the top of the floor is  completed, and the yellow tape is covering the holes in preparation for spraying  from the bottom.  
  


Of course all the seams are sealed.



Here is the driver's side wheel well with the Lizard Skin applied and with the urethane paint coating.
This combination should look good and be easy to keep clean for a long time!


Finally, here's a sneak peek at a finished door...black paint so shiny and deep you can use it for a mirror.
I can't wait to see the finished car!

Progress Report

Things are starting to come together!  John, my body guy, is finished using the chassis as a template for the body fitting and has the body tub mounted on a jig for the final prep and painting.


Now I needed to bring the rolling chassis back home to get the engine and gearbox mounted in place.



 First on my to do list was to get the clutch installed on the engine, and an important step is installing the 3 dowel pins (in the face of the flywheel) that will align the clutch. In addition, the rear engine mounting plate has two dowels that will align the gear box.



The new Sachs clutch was part of the TRF "magic clutch kit"....all the parts you need for a new clutch installation.



The TRF kit includes a new Koyo throw out bearing, cross shaft, fork, and bushings. Following the advice of seasoned TR6 owners, I drilled the fork and shaft and added an additional bolt to supplement the safety wired pin that holds the fork/shaft together. 


Mating the gear box and engine together was a bit of a challenge, but a sling up to the rafter allowed me to position the gearbox so it went together with a satisfying click ! 


Ok, let's try and get this bad boy back on the chassis !



Ever so slowly lowering the engine back in place...


Lots of wiggling brought success !


Once the engine and gearbox were bolted down, I couldn't resist installing my Good Parts header. Because this header is coated with Jet Hot Coating, it should look this good for a long time !



Getting the drive shaft re-installed with new Neapco universal joints came next. 


I "roughed in " the exhaust system, marked the various pipes, then removed it, as the final installation will require having the body tub back in place.



John tells me he is painting the body tub and body panels, so this chassis will soon be going back to his body shop to have the body lowered back into place....stay tuned!

Time to Upgrade the Man Cave Floor

Before Tillie the TR6 came into my life, my garage was used to keep our daily driver car, motorcycle, lawn mower, snow-blower, etc, out of the weather. Over the years the concrete floor has taken a real beating with salt slush off the car in the winter, oil drops, and just plain wear and tear.


Well, now that the messy part of the TR6 restoration is done, and I've turned the garage into a man cave/shop, I began thinking about doing something with the floor. I needed to keep the cost under control, so having the floor removed and new concrete poured was not an option, plus the thought of moving everything into a storage unit for a month didn't sound like fun. Several years ago I looked at various floor coatings / coverings and ended up buying an inexpensive, rubber mat material that was interlocking for the worse half of the floor... Ok, but not what I really wanted for the long haul.


 An internet search turned up SnapLock Industries in Utah that makes interlocking modules out of polypropylene and markets them under the RaceDeck name. RaceDeck flooring is not affected by common automotive chemicals, like oil, brake fluid, grease, etc, and can support thousands of pounds of weight...just don't weld over it ! All this and it is 100% made in the USA and comes in 10 colors!  Several times a year, RaceDeck puts their flooring on sale and includes free shipping, so when their March sale notice arrived, I called them and pulled the trigger on enough flooring to cover my 16' X 16' floor....graphite in color with a black border and black edging. Four business days later, 7 boxes weighing about 250 lbs total arrived....glad I didn't have to pay the UPS cost for shipping !


The worst part of this project was getting all my "stuff"out the of  Man Cave! I cleared one side at a time then thoroughly cleaned the concrete with a broom and compressed air.


A close look at the tile underside shows the "male" peg and the "female" loop that snap together.


The underside of the tile is designed to hold over 5K lbs of rolling weight, yet allows  air to circulate... keeping mold and mildew from forming.



The tiles are 1/2" thick.



Since the flooring snaps together, the only tool you need is a rubber mallet to tap the tiles into place.


The directions tell you to start in a corner.


The boxes came with four tiles already snapped together, twelve deep.  



The "female" loops are to be pointed in the direction you are moving.



Covering up those nasty cracks!


Even the edges are made to support a lot of weight !




The finished product !  My wife thinks that the new floor gives a real boost to the whole property ! :-)

 

 
Now we're ready for Tillie's body tub when it returns from the body shop later this spring !