A Bleeding Good Time !

Since Tillie is going through a complete ground up restoration, new brake lines and all related brake components have been either rebuilt or replaced.  Same with the clutch, all new or rebuilt. So, I've put all those components together and now comes the moment of truth...adding the brake fluid and seeing what leaks !

I had heard enough horror stories on the 6-Pack forum about paint damage caused by DOT 3 or 4 brake fluid, so the decision to use the more expensive DOT 5 was a no brainer. Dot 5 is silicone based and will not eat your fancy paint job for lunch, where as DOT 3 & 4 are glycol based and will damage that expensive paint job.  One of the big problems of switching over to DOT 5 is that it is not compatible with DOT 3 or 4, but in my case, everything was new and dry, so no old fluids to worry about.



I'd like to say that all my connections were solid with no leaks, but that's not the way it happened...I wiped up more brake fluid than I care to admit, but hey, there are a lot of  pipe joints....

The PDWA switch is used to alert the driver if one of the two brake circuits goes bad. This simple device has just two rubber "O" rings that can leak, and yep, mine leaked. I had  used the wrong size "O" rings.  :-(


 Front Brake Flex Lines


 Front Brake Calipers


 Rear Brake Wheel Cylinder


 Rear brake flex lines..well, you get the idea....lots of joints that have to be perfect, and they are...now.  ;-)


The hydraulic brake and clutch can't have any air in the lines in order to function properly, so getting that air out (once the leaks are fixed) is very important.
Growing up, my job was always the "pumper" when it came time to bleed the brake lines after replacing the brake shoes on the family's '58 Ford.  I'd sit in the car and my dad would be at the wheel opening. He would use an end wrench and a tube ( connected to the wheel cylinder bleeder) that went into a jar used to catch the brake fluid. He'd say, "push the brake pedal and hold it."  Dad would then open the bleeder, watch for the air bubbles / fluid to come out, then close the bleeder and tell me to repeat the push and hold process. Once just fluid and no air came out of that particular wheel cylinder, he'd move on to the next wheel after adding more fluid to the master cylinder. This method still works, but I figured there had to be an easier, one- person way to accomplish this task, so I did what any 21st century person would do...I did a Google search on bleeding brakes!

 I found lots of options, but Phoenix Systems makes a one- person bleeder that can do a reverse bleed process. It pulls the fluid out of the container at the wheel and pushes it up to the master cylinder. This seemed to work pretty good once the leaks were fixed, but even the directions that come with it say that you may need to pump fluid from the master cylinder back to the wheel cylinder to get rid of all the air, and I still had air in the lines.



After several hours of "messing" around trying to get all the air out, I took a break and did what I should have done in the beginning ....I did a search on the 6-Pack forum regarding bleeding brakes. When I came across the term "Speed Bleeder", learned how it works, (a small ball bearing and spring that keep out unwanted air), I got on eBay and ordered a set for all four wheels and one for the clutch slave cylinder.


The eBay vendor is located here in Ohio, so I had my new bleeders in two days. The idea behind these little jewels is that one person can crack open the bleeder then pump the brake pedal (without needing a second person). The ball bearing and spring close off the bleeder when you release the brake pedal. Now ideally, a second person could watch the fluid as it comes out of the bleeder and tell you when no more air bubbles appear, I just kept pumping until no bubbles were in the drain line and catch bottle.



 I was finally getting close, but the brake pedal still went almost to the floor before getting solid, and  I knew something was still not right. More 6-Pack forum searches produced my answer....I needed to adjust the rear brakes up solid, then back the adjuster off one quarter turn. Bingo, the brake pedal felt  perfect.



The clutch on a TR6 is hydraulic with a master cylinder and a slave cylinder. Once I got the solid pipe and flexible braided line installed, the speed bleeder made easy work of getting rid of the air.

Master Cylinder


Slave cylinder with drain tube attached to the bleeder.


Oh, there was just one little problem. It looks like there is plenty of fluid in the clutch master cylinder, but that amount is only good for about 4 pushes on the clutch pedal....try for a 5th push and you will hear a sucking sound. ARRGH, I just sucked air back into the line.  Start over and be more careful !



I'm quite confident my brakes and clutch are road worthy, but on this type of restoration it will be months before I can do a road test, so I'm going to move on to the radiator...stay tuned !

Aluminum Fuel Tank

Tillie's fuel tank had a lot of "gunk" laying in the bottom, so I knew I needed to do something....either have the original steel repaired, replace the original tank with a new steel tank, or replace the original with a Bastuck aluminum alloy tank. Wife Rhoda pushed me to go with the more expensive aluminum tank...what a Woman!!

The original tank had been repaired at some time in the past, but a flash light inspection showed up rusty spots just waiting to clog up my triple ZS carbs !




The only vendor here in the U.S. that I could find who carries the German- made Bastuck aluminum alloy fuel tank is BPNW (British Parts North West).  Most of the time the tanks are not in stock, so in early January 2012, when I saw they had some available, I wasted no time ordering one.


 These tanks are made to bolt in exactly like the originals, plus they look very cool.


The Triumph factory originally put a strip of felt under the tank for noise control where the tank rests on the floor....I figured these stick-on felt furniture disks would do the same job.


I had already installed a new stainless steel fuel line, so getting new tank hardware seemed to make sense.


Replacing  the tank sending unit will help ensure an accurate fuel gauge.



The tank venting canister was long gone, so I decided to vent the tank through a K&N vent filter located directly below the trunk area of the car.



6-Pack members also recommenced putting a shut off valve in the fuel line...easy to do at this point. 



All installed....gosh, this is almost too pretty to cover up !



Once the tank installation was completed, I finished all the fuel connections up to the fuel pump.


S/S Exhaust System

Choosing the "right" exhaust system was something that evolved for me over the past two years.  Early on I decided on stainless steel, but ,should I stay with the original design, or go with a more sporty system? The issue got settled in my mind when Bob,one of the 6-Pack members from NY state, posted pictures of his "Bell Sport" system!
All S/S construction and slash cut tips ! 

The Bell Exhausts are made in England and imported by Engel Imports located in Kalamazoo, MI.  For several months, the system that I wanted was on back order, but then in February 2012 the system became available, and I pulled the trigger on my order... less than a week later, it was in my shop!




Of course the primary goal of a exhaust system is to allow the engine to breath freely with out excessive noise. The stock exhaust manifold is considered my many to be a very good design, but dyno testing has proven a well designed / constructed exhaust header will free up more horse power.
 Richard Good of "Good Parts" has been making the TR6 handle better and produce more power for over 20 years, so when he came out with his 6 into 1 header, I knew I had found the final piece to my exhaust system design. Richard hand makes these headers and then sends them off to be "Jet Hot" coated inside and out.

 The Jet Hot coating not only looks terrific but will keep its shine, and it also lowers the temperature under the hood.


 This adapter allows the header to work with a dual exhaust system 



While just the rolling chassis was in my shop for the engine installation, I "rough" fitted the exhaust while I had easy access to the frame. When I pulled the exhaust off, I laid the various parts on the floor one at a time and marked all the pipes left / right, front  / rear, etc.



During the initial fitting, I discovered that due to the length of the header, I needed to cut approx. 6" off the front pipes.



Also during the initial fitting, I decided to wrap the pipe closest to the fuel line / brake line with exhaust wrap to help keep the temperature in check.


 The initial fitting also showed me I'd need to create an extra bracket to hang the mufflers.


Several 6-Pack members had reported having problems getting the S/S pipes to seal at the joints.The fix was reported to be the use of a high temp gasket maker in the joints along with wide S/S band clamps.  The clamps will also allow for the removal of the exhaust if ever needed.


Getting the mufflers to hang correctly took quite a bit of measuring  and fiddling !




I wanted the exhaust tips to match...there's nothing that shouts "amateur" like uneven pipes !


I'm discovering that when you rebuild a car from the ground up, there is a lot of "waiting" time. I'd love to hear how this exhaust sounds and if the joints are sealed up correctly, but I have a long way to go before firing up the engine for the first time, so I just keep plugging away.

Putting Those Parts Back Together !

When rebuilding a car from the ground up, you quickly come to realize that there are A LOT of small pieces and parts! Falling in this category with those small parts you take for granted are the windshield wipers

 The wipers on a TR6 work via a cable that slides back and forth in metal tubes buried in the scuttle above the firewall. If that sounds hard to imagine, you're right, and it's even harder to install !


The wiper wheel assembly holds the tubes for the cable to ride in, allowing the cable to engage the teeth of the wheel.  The other side of the assembly sticks up through the body work for attaching the wiper arm.


Yeah, just grease up the parts then try and put them together in a little 2" X 3" opening ! 


This is the end of the wiper cable that will attach to the wiper motor...the pull on this cable has to be less than 6 lbs. so as not to burn up the motor!


Once the cable, tubes, and wiper wheel assemblies are in place and operating smoothly, you seal up the openings.


All ready for the wiper arms.




Moving on...when you're taking parts off the car, the sequence of removal isn't too important, but guess what, when you're putting them back on, the sequence becomes VERY important !

I give you exhibit "A" ... the pipe that returns coolant from the heater back to the water pump and is tucked in next to the block... 


Once the exhaust manifold and carburetors are installed, it's almost impossible to slide that pipe into position...don't you wonder how I found that out?  Yep, the hard way ! 


Make sure you put the throttle pedal in before you put in the pedal box. I got this right the first time !


The brake/clutch pedals need to be installed in the pedal box before the box is mounted in the car, and be careful not to reverse the two pedals. Thanks to a recent 6-Pack thread, I also got this right the first time !


The brake and clutch master cylinders go on after the pedal box is installed...I thought they went on awfully easy the first time. )-:  Got it right the second time !

Heater Box Restoration

In my previous blog I mentioned "go to" guys that rebuilt various components for me.  For the heater box, I'm the "go to" guy!  Tillie's heater box is buried up under the dash, so it's one of the first things to get installed during a rebuild. There are only two parts to go bad in a heater box...the electric motor that runs the fan, and the heater core that the hot coolant flows through. With that in mind, I ordered a new heater core from TRF and a new fan motor.  The core was in stock and shipped within two days of my order, but the electric motor was on back-order. No problem, I thought, as I've got at least two months before I need it. Well, over three months went by and no sign of my fan motor. A call to TRF brought no joy...they had no delivery date.

Old fan motor.
I tried taking my fan motor to a local auto electric shop for rebuilding....the guy behind the counter took one look at it and gave it back,saying, "Sorry, no parts, I can't help you."  


Well, this is the 21st century, so I did an internet search and found a web site for Holden Vintage & Classic Ltd. in the UK.  They carry electric motors(among other things) for various old British cars, and I soon found a motor that had the same specs as my original. Even after the conversion from Pounds to Dollars and shipping from England, the cost came in less than the TRF unit. 



The heater box is truly just a metal box that holds the heater core and the fan assembly, so I simply took out all the screws ( after taking pictures) and pulled it apart. My body tub was at the media blaster's at this time, so I gathered up all the heater box metal and took it out to Roy for cleaning.

Before

All good solid metal, just gunky and dirty after 40 years of use !



A few of the pieces after priming and painting






Old heater core


 New replacement core from TRF


Back in place !

This is a pretty straight forward part to rebuild. Just take plenty of pictures during the dis-assembly process. After I was done, I did find out through the 6-Pack that there is a gentleman in California who rebuilds the fan motors, and if you don't want the cost of a new core, any radiator shop will pressure test / repair your existing core.  One more thought just came to mind... be very careful with the plastic fan unit when you pull it off the electric motor. They are not available new, so you would have to find a used one if you break it !